Video

ALTISTART 46 MANUAL PDF

Description: This users manual for Altistart 46 soft start motor controllers contains installation, setup, operation, and maintenance instructions. User’s manual ATS46, 9/21/18, English, Spanish, French, pdf MB. Data Bulletin. Cross Reference Guide for ALTISTARTĀ® 46 Soft Start Motor. User’s manual UNI-TELWAY ATS VW3G, 12/13/17, English, pdf MB. Programming manual ATS VW3G, 12/13/17, English.

Author: Meztijora Voodoolkis
Country: United Arab Emirates
Language: English (Spanish)
Genre: Science
Published (Last): 16 November 2018
Pages: 252
PDF File Size: 18.4 Mb
ePub File Size: 8.59 Mb
ISBN: 531-1-64123-489-3
Downloads: 73511
Price: Free* [*Free Regsitration Required]
Uploader: Kajijar

Altistart 46

Cable too long between motor and starter 1. Remove the transformer by unscrewing the CHC screws using a 4 mm Allen key. Core housing Material U.

The quality of the replacement service is based on stocks constituted at Evreux, in the branches and by the official dealers. Strip the wire and insert it in the clips. Connect the connector of the current transformer cable to J 43 on the electronic card, observing the wire coding.

It’s a community-based project which helps to repair anything. Consult the schedules to make the best choice. Up to now experience: The motor starts if a 2-wire control is on TBS value equal to 0 during powering up, even though its value is different refused of to reset to zero the parameter TFR hourmeter when the engine is running on-factory adjustment of parameters IPR, TPR and TBS local mode used only upon the first product powering up assignment of LI to LII motor preheating or LIH faults inhibition default startup time when loaded went to 4 seconds removal of the starter thermal protection calculated by the software on C11, C17, C21, C25 and C32 calibre readjustment of the rated current value by on-factory setting A for M12 calibre correction of the anomaly concerning the micro controller upon unshunting with the bypass function correction of the anomaly following a simultaneous running instruction with a stopping instruction.

  CLASIFICACION PLAQUETOPENIA PDF

Care should be taken to ensure that this card is positioned correctly, placing the connectors towards altistzrt top of the unit. Remove the connectors located at the base of the product.

They are also manufactured and tested at Schneider factory at Pacy Blanchet. Cut the existing ribbon cable and connect the new ribbon cable using the two crimping terminal lugs provided. The following instructions have to be performed: Avoid the current pulse in the engine as well as startup in current kanual correction of the anomaly concerning a random startup following a series of transient power cutoffs. The starter supplies current but the motor does not run. Conversion instructions for sizes 4 and 5 Remove the fan grille by tilting it backwards after first loosening the screws on the front 7 mm open-ended spanner.

J7 Connector if pump unit J9 J10 J11 rear view of the control module 5 – Remove the connectors from the vigitherm and the current transformers. Reference Rated ef f. Insulation defect between via of altixtart printed circuit metal hole allowing to connect two faces of a printed circuit and R resistance control card. Value kept for the test voltage 2 V AC high voltage wiring supply For floppy disc 2, follow altistarr instructions that will appear on the PC screen.

Altishart knowledge of ATS46 functionality is necessary to repair at best theses products. Phases off-balance due to insulation defect on IT rate 1.

Starter disrupted by a DC converter 1. Use the fixing points to run the cables along the insulating dividers and connect up to the clips.

User’s manual ATS46

Do not soak attach brackets in the indicated areas. 446 the cable to the penultimate right-hand plug-in unit for a size 4 starter or to the centre of the starter for a size 5. Low torque at start tQ0. The time taken to perform the conversion is approximately two hours, to which site transfer time must be added.

  DRILLCO CATALOG PDF

Altistart-Ā« 46 Soft Start Motor Controllers Users Manual | Schneider Electric

M Has to be fixed on one of the assembling screw before soaking Red wire mark 4: Session program is included in appendix. If the cables are too short, use the TI ribbon cable which is part of the kit. Conversion instructions for size 3 8 – Remove the six screws from the fan mounting plate. Use of a self maintained bypass with external thermal protection. For more information, please contact S.

Value kept for the test voltage 2 V AC Seco nd ar y: Insert floppy disc 1 in drive A, 3. Assembly size 1 Wltistart list Part 2: Phase rotation fault assignment Function Phase rotation detection PiF Phase rotation state The function is active at each start order. altistaft

No aaltistart out of the transformer lower part 2 mm minimum mandatory Outlet order is not important. J 49 Follow the diagram: Possibility of line fuse melting. If the conditions are dif ferent, they have to be specified in chapter 7: Starting end on a high inertia, low opposing torque application.

White Green Blue Red diagram of the customer terminal block 12 – Remove the four screws attaching the transformer no. Connect the cable with 2 red wires to J42 on the electronic mannual.